Fabric Folding Machine
all
Fabric Inspection Machine
Fabric Folding Machine
Fabric Cutting Machine
Beam Stacker
Digital Counter Meter
Fabric Relaxing Machine
Tubular Fabric Reversing Machine
Tubular Fabric Slitting Machine
Automatic Tube-Sewing Machine
Hydraulic Warp Beam Trolley
Motorized Warp Beam Trolley
Cloth Roll Trolley
Warp Beam
SUNTECH Service
Fabric Rolling Machine
Fabric Roll Packing Machine
Accessories
Batcher Machine

Fabric Folding Machine

How to align the fabric edges well on Fabric Folding Machine?

1- Take off all the fabric from fabric folding machine.2- Check the cloth guiders, make sure the distance between two side clothe guiders to two side beams is same.3- Set the button of "sensitiveness adjusting" between 6 & 7.4- After finishing above three steps, loading the fabric on fabric folding machine, After fabric folded by triangle frame, the folded fabric will go through the edge-alignment raster. Make sure the fabric edge is in the detecting range of edge-alignment raster.5- Then start the machine, running the machine for a short time, then stop the machine.6- At the position of edge-alignment raster, please check which side of the fabric edge is deviating. Then turn the "balance adjusting" button to make the raster moving to the contrary side, until the doubled edges are well aligned. So the balance adjusting is in the best parameter. Re-start the machine, it will work properly.

How to control the crease problem on Fabric Folding Machine

The key factor of "crease" issue is the height of triangle frame. Adjust the  triangle frame to a heigher position by adjusting the support rod on Fabric Folding Machine

Is Suntech Fabric Folding Machine suitable for mesh net fabric?

Yes, we have upgraded the Fabric Folding Machine to be suitable for mesh net fabric.1.We add one Motor at the fabric feeding position, which could feed fabric automatically without stretching.2. Adding Electrical Tension Control, we will make sure the speed of fabric feeding, checking and rewinding are synchronized. The dancing roller is specially designed for tension control. The dancing roller will move up and down to control the fabric tension.3.Adding Magnetic Powder Clutch, controlling the fabric tension before lapping, avoiding fabric stretching.

ST-DFLM How to make sure fabric folded selvege to selvege

1. TAKE OFF ALL THE FABRIC FROM FOLDING MACHINE. 2. CHECK THE CLOTH GUIDERS, MAKE SURE THEY ARE SYMMETRICAL. 3. HOW TO SOLVE THE ‘’CREASE’’ ISSUE:THE KEY FACTOR OF ‘’CREASE’’ ISSUE IS THE HEIGHT OF TRIANGLE FRAME.AND PLEASE ADJUST THE TRIANGLE FRAME TO A HIGHER POSITION BY BELOW TWO PARTS:   NOTE: PLEASE ADJUST THE TRIANGLE FRAME HEIGHT TO A HIGHER POSITION SIGHTLY, AND OPERATOR NEED TO ADJUST THE HEIGHT BASED ON DIFFERENT FABRIC TYPE.  4. HOW TO SOLVE THE ‘’EDGE-ALIGNMENT’’ ISSUE: 1) PLEASE SET THE BUTTON OF ‘’SENSITIVENESS ADJUSTING’’ BETWEEN 6 AND 7. 2) WHEN OPERATOR HAS FINISHED ALL ABOVE THREE STEPS, OPERATOR CAN LOAD THE FABRIC INTO THE MACHINE, SURELY OPERATOR NEED TO MAKE SURE THAT ALL THE FABRICS ARE IN WELL ALIGNED POSITION BY HAND BEFORE MACHINE STARTING.3) THEN OPERATOR CAN START THE MACHINE SLOWLY, AND MAKE THE MACHINE RUN FOR A SHORT TIME, THEN STOP THE MACHINE.4) THEN AT THE POSITION OF EDGE-ALIGNMENT RASTER, OPERATOR NEED TO CHECK WHICH SIDE OF THE FABRIC EDGE IS DEVIATING, THEN OPERATOR NEED TO TURN THE ‘’BALANCE ADJUSTING’’ BUTTON TO MAKE THE RASTER MOVING TO THE CONTRARY SIDE, UNTIL THE DOUBLED EDGES ARE WELL ALIGNED. SO THE BALANCE ADJUSTING IS IN BEST PARAMETER. AND THEN OPERATOR CAN RE-START THE MACHINE, WHICH WILL WORK PROPERLY. FOR EXAMPLE, IN BELOW PHOTO, THE FABRIC EDGE IS DEVIATING TO OPERATOR’S RIGHT SIDE, THEN OPERATOR CAN GO TO THE CONTROLLER OF ‘’BALANCING ADJUSTING’’, AND TURN THE BUTTON TO MAKE THE EDGE-ALIGNMENT MOVE TO LEFT SIDE UNTIL THE FOLDED EDGES ARE IN WELL ALIGNED POSITION. THEN OPERATOR CAN RE-START THE MACHINE TO SEE PERFORMANCE.    

How to ensure selvage well aligned after fabric folding machine?

ST-DFLM / ST-DFRM1) Cloth Guider:Adjust the pair of cloth guider to the optimal working condition, which could keep fabric in the center.2) Folding Triangle FrameAdjust Folding Triangle Frame as per actual situation.3) Fabric-limit BarAfter folding on the Folding Triangle Frame, the folded fabric should go through the fabric-limit bar and operator should align the two edges by hand at this part.4) Edge-Alignment RasterAdjust the position of the Edge-alignment Raster and make sure the two edges of fabric are within the detecting range of Raster.ST-DFLM Double Folding And Lapping MachineST-DFRM Double Folding And Rolling Machine