FAQ
All
Fabric Inspection Machine
Fabric Folding Machine
Fabric Cutting Machine
Beam Stacker
Digital Counter Meter
Fabric Relaxing Machine
Tubular Fabric Reversing Machine
Tubular Fabric Slitting Machine
Automatic Tube-Sewing Machine
Hydraulic Warp Beam Trolley
Motorized Warp Beam Trolley
Cloth Roll Trolley
Warp Beam
SUNTECH Service
Fabric Rolling Machine
Fabric Roll Packing Machine
Accessories
Batcher Machine

all

How does the weighing device convert "kg" to "pounds"?

How does the weighing device convert "kg" to "pounds"? 1) Keep pressing "Function Button" until it shows "P1-1". 2) Press "Tare Button" to change the number to "2".3) Press "# Button" to finish this process. ST-DCM Digital Counter Meter ST-SP-CG Electrical Cloth Guider

16. When the machine is start, the fabric from Encoder Wheel to rewinging roller can not be measured

ST-WFIM length from Wheel type Encoder to Rewinder roller(L1) can not be measured, because at this time, the digital counter meter does not start to count. After machine start, the operator will cut the fabric roll by Linear Fabric Cutter, the fabric length from Wheel type Encoder to Rewinder roller(L2) at this time is measured. But Linear Fabric End Cutter cut the fabric at rewinding position, the L2 is remain on the machine, and L2=L1, so the final length measurement is accurate, the error is very very small. 机器开始计长时,从轮型编码器到最后收卷处这一段面料的长度是不是不会被计长,因此导致计长不准确?首先,当机器运行时这一段是不会被测量到,因为这一段属于运行前穿布,但是最后测量长度依然是准确的,因为最后断布刀断布的时候从轮型编码器到收卷辊筒这一段会被留在机器上,而这段是被计长的,刚好抵消之前不被测量到的面料长度,所以误差很小。

Can you provide fully automatic fabric end cutter?

Can you provide fully automatic fabric end cutter? We do not provide fully automatic fabric end cutter, and we normally only recommend customers to use the semi-automatic cutter, because the fully automatic cutter may cause harm to operator when sometimes the cutter can not collect the signal from obstacle correctly and timely.1) Linear Fabric End Cutter is used to cut all kinds of fabrics, the Max.Cutting Height is 10mm.2) For 1800mm width cutting, the weight of Linear Fabric End Cutter is 11kgs (cutter+guide)3) If the Max.Length of guide is 1900mm, the Max.Fabric Width it can cut is 1700mm. 我们不提供全自动断布刀,我们只推荐半自动断布刀,因为全自动断布刀会因为信号手机不确认或者不及时,导致对操作人员产生伤害。2)ST-SP-LC 断布刀 (Linear Fabric End Cutter)          1.断布刀主要是用来切面料,切割的最大厚度是10mm。2.1.8 门幅,断布刀加导轨重量是11kgs3.1.9M导轨最宽可以切1.7 M门幅 ST-KFIM-01 it is suitable for a wide range of fabrics,from tension-senstive elastomeric and lycra fabrics to stable woven,technical and upholstery materials. ST-HRM it is horizontal fabric rolling machine is used to handle a wide range of rolled fabrics which is specially designed for garment factory and fabric distributor.

Why we do not recommend to buy the 4-point system if customer only buy one set of Fabric Inspection

If you just have 2 sets of inspection machine, we don't recommend it, because the function just can used to record the general information and defect types, locations & serious degree. If you have 5 sets, 10 sets or more sets of inspection machine, this system also can connect together to be as a intranet, share all the information. The production manager could monitor every machine's processing on the head computer, manage production plan, control the inventory, analysis the statistics to improve the quality.  如果只有两台,或两台以下的验布机,我们不推荐,四分制系统只能记录一些普通信息(班次,批次,操作人员)和疵点的位置、类别、严重程度。如果你有5台,10台或更多的验布机,可以把每台带有4分制系统的电脑连接起来,形成一个局域网共享信息。在这个局域网内,生产经理在总机上可以检测每一台机器的运行,(知道每一台机器的疵点情况)制定生产计划,控制存货,通过分析数据来该进质量。(多台验布机放在不同的地方,生产经理只要在一台电脑上就可以知道所有验布机的验布情况,方便管理。) ST-KFIM Knitted Fabric Inspection Machine ST-KFIM-01 Open-width Fabric Inspection Machine

How to operate the 4-point system?

 How to operate the 4-point system? 1)Install the software into the computer and connected the computer with the machine2)You need identify 24 defects onto the software in the computer and the computer will record some general information you input like date, order, shift, operator's name, in the copmputer3)When the operator found defects when inspecting, manully stop the machine, select defects and give penalty from 1-4 serious degree on operation panel.4)the computer will record the type, the position and the serious degree of the detects. The printer prints the results. 1)把软件装到电脑上,电脑与机器相连,2)在电脑上定义24种疵点,电脑可记录批次,班次,操作人员等(人工输入)3)开机运行,发现疵点,停车,操作人员根据疵点的特点在操作面板上按相应的数字,按严重程度扣分,继续检验4)电脑上会记录疵点的位置、类别、严重程度,打印机打印报告 ST-KFIM-01 It is suitable for a wide range of fabrics,from tension-sensitive elastomeric and lycra to stable woven ST-KFIM It is suitable for a wide range of fabrics,from tension-sensitive elastomeric and lycra to stable woven

What is 4-point System?

 What is 4-point System? Faults Recording System/Software adopts America 4-point Standard, which could record 24 defects (customized), these defects could be given penalty from 1-4 serious degree on operation panel. The more serious of defects, the more penalty will be given. 采用美国四分制标准,这个软件可以记录24位疵点,这些疵点可以自定义。疵点可以被划分为四个等级,按照 疵点的严重程度扣分,越严重扣的分越多。 Related Products! ST-KFIM-01 It is suitable for a wide range of fabrics from tension-sensitive elastomeric and lycra fabrics to stable woven,technical and upholstery materials ST-KFIM It is suitable for a wide range of fabrics from tension-sensitive elastomeric and lycra fabrics to stable woven,technical and upholstery materials

Does the machine have a guard or shut off switch or sensor ?(ST-WFIM)

Does the machine have a guard or shut off switch or sensor ?(ST-WFIM) 1-There is a shut off switch on operation panel (in below red), in case someone puts their hand near the rollers, press the button, the machine will stop running. 2-Normally, the rolling speed is 15m/min, this speed is safe enough, and there is a enough gap between two rewinding rollers, in case someone puts their hand into the rollers,the hand will not be rolled and hurted because of the safety speed and enough gap.3. We do not suggest you to add the sensor or guard.3.1)Adding a sensor to induce the anything near the roller, the machine will stop immediately, this idea is perfect, but it's not working actually.Suppose the operator need to check the roller during machine running or to adjust the rollers as per the actual condition, the sensor may induce the operator and stop the machine.2)If the guard is added on rewinding position, it will be much more complicated for fabric feeding and fabric roller doffing, the operator may need to bend over allthe time. And the machine price will be much higher.

How to adjust the rewinding roll tightness(ST-WFIM )?

How to adjust the rewinding roll tightness(ST-WFIM )? The hand wheel could adjust the speed difference of two pulleys. The two pulleys are connected with the twin rewinding rollers separately. If there is speed difference between the two pulleys, there is also speed difference between the two rewinding rollers which could result in tight or loose fabric rolls. In this respect, the hand wheel could control the roll tightness through different speed. 手轮可以调节两个皮带轮的速度差。两个皮带轮各自和两个收卷辊筒连接,如果两个皮带轮有速度差,那么两根收卷辊筒的也有速度差,就能产生紧或松的布卷。所以,手轮可以通过调节速度差也控制松紧程度。 ST-WFIM Suntech Woven Fabric inspection machine ST-SFIM Suntech Simple Fabric inspection machine

How much fabric is it needed to wind the machine?

How much fabric is it needed to wind the machine? Q:The rolls I work with are of 50 yds(45.7m), and I am seeing that the process to wind the rolls is a very long process and it requires a lot of fabric. How much fabric is it needed to wind the machine? Because I calculate 10 yds approximately and 10 yards out of a 50 yd roll will be a lot of fabric that will not be inspected? A:The whole process of feeding the fabric on the machine is around 3.5m, and it is just around1.5m below the inspection screen, which can not be inspected. For inspecting every roll, we recommend to add a fabric end stop sensor at feeding position, when it detects there is no coming fabric, the machine will stop automatically to let the operator join the next roll. In this way, there will be no fabric can’t be inspected in the next rolls.  穿布的长度是多少? 穿布的这段面料是否可以检验?我的每卷面料是50m, 如果穿布的面料不能检验的话,是不是我每次换一个卷的时候,就会浪费一部分3.不能检验的面料?整机的穿布行程是around3.5m,验布台以下是around1.5m。可以在入布处加无布停车光电,当光电检测到没有布料输入时,机器会自动停下来,方便操作人员接上布,可以减少穿布。这样除了第一匹布之外,接下来的每一匹布整匹都能检测到。 ST-BM It is suitable for a wide range of fabrics,especially for continuous process A-frame batch and re-winding to small rolls.this machine can provide synchronized fabric input or output to A frame with peripheral fabric contact for delicate or heavy fabrics ST-KFIM ST-KFIM-01 is suitable for a wide range of fabrics, from tension-sensitive elastomeric and lycra fabrics to stable woven, technical and upholstery materials.

How to adjust the sensitivity of edge-alignment photo sensor?

How to adjust the sensitivity of edge-alignment photo sensor? This is a title There is an Edge Detection Switch (in blue) on Edge-Alignment Photo Sensor, operator could use screwdriver to adjust the switch, rotating the switch to more right, the sensitivity will be higher.对边光电远布端有一个蓝色的旋钮(探边开关),用一字螺丝刀往右旋,灵敏度越高 ST-KFIM It is suitable for a wide range of fabrics,from tension-sensitive elastomeric and lycra fabrics to stable woven,technical and upholstery especially designed for A-frame entry with conveyor belt system.

How does this machine control the edge-alignment?

3.How does this machine control the edge-alignment? One set of Edge-alignment Photo Sensor which is installed at one side of fabric edge to detect whether it is deflective . When the sensor detected the edge is not aligned, the Rewinding Station will move left or right to make the edge aligned.  机器的其中一侧装有一个对边光电来探测布有没有偏离。当光电探测到布边没有对齐时,移动小车会左右移动使布边对齐 Suntech textile machinery Our experience in textile industry(fabric finishing and weaving & spinning accessories) can be traced back to 1970,with more than 40 year experience.our company website:one: http://www.suntech-machine.com;two: http://www.strength-machinery.com     Suntech,the first company,is one of the leading designer and manufacturer on textile machinery for both weaving and finishing units.by now Suntech has become a significant name in textile machinery market with more than 4000 customers and 10000 installations in global.    STRENGTH,the second company build in 2013,is specialized weaving & spinning accessories.with rich textile machinery experience,excellent sales team ,and quality service system,STRENGTH build strategic relationship with first-class factories in China,aiming to provide you one-stop purchasing service,and to be the world's largest trading platform of textile machinery accessories and parts.Mr. ShenYoutube:https://www.youtube.com/channel/UCxZDZ7QI0w5pzVDrb83vdNAE-mail: sales@suntech-machinery.comWebpage: www.suntech-machine.comfacebook:https://www.facebook.com/suntechmachinery/?epa=SEARCH_BOXwechat/phone number:13777818208email address: sales20@suntech-machinery.comwhatsapp/phone no: +86 15657131110wechat: zw850521173 ST-KFIM-01 It's suitable for a wide range of fabrics,from tension-sensitive elastomeric and lycra fabrics to stable woven. ST-WFIM It's suitable for a wide range of woven materials ,inculding denim fabrics

For your model ST-WFIM-320, can it be used to inspect fabric in width 1200mm?

Woven Fabric inspection Machine Normally for model ST-WFIM-320, its most suitable fabric width is 1600-3200mm.Because if the fabric width is too narrow on a wider working width machine , the roller will be deformed after long time using. Therefore, we would like to recommend this proposal for you:To buy a ST-WFIM-180: suitable for fabric width 900-1800mmTo buy a ST-WFIM-320: suitable for fabric width 1800-3200mm. 2.ST-WFIM-320,可以适用于检验门幅是1200mm的面料么?通常情况下,ST-WFIM-320最好是适用于1600-3200mm的面料。因为如果使用门幅较窄的面料,机器的辊筒在长时间使用之后会变形。如果你的门幅范围较大,我们建议你以下方案:买一台ST-WFIM-180:适用于门幅900-1800mm的面料;买一台ST-WFIM-320:适用于门幅1800-3200mm的面料; ST-WFIM It is suitable for a wide range of woven materials,inculding deim fabrics. ST-SFIM It is suitable for a wide range of fabrics,from tension-sensitive elasto-meric and lycra fabrics to stable woven,technicial and uphplstery materials.

1.How to install the cloth guider?(ST-KFIM Knitted fabric inspection machine)

Put the fabric in the center of the machine and the cloth guider on the both sides of fabric.Please make sure each cloth guider has the same distance to its each correspondent beam. The cloth guider will avoid fabric deviation, to place fabric in machine center. 将面料放在机器正中间,吸边器夹在面料的两端。一个吸边器到横梁一端的距离与另一个吸边器到另一端的距离相等。如下图所示,需要DISTANCE 1=DISTANCE  吸边器的作用:保证面料一直在机器的中间,不跑偏。(不能用于针织布,容易变形) ST-KFIM-01 Knitting fabric inspection machine is suitable for a wide range of fabrics,from tension-sensitive elastomeric and lycra fabrics to stable woven. ST-KFIM Knitting fabric inspection machine is suitable for a wide range of fabrics,from tension-sensitive elastomeric and lycra fabrics to stable woven.

If there is any problem within warranty period, how you solve the issue?

Regarding this machine, we use Japanese imported alloy cutting blade,which is three times durable than normal cutting blade. And we have sold lots of this machine,all the feedbacks from our current customers are positive. So we are confident about our quality. If there is any questions occurred within warranty time, we will be fully responsible and send you free spares immediately. It just takes 3-5 days by express. And if questions occurred beyond warranty time, we will also try our best to solve with you together.